Free Gadget Manuals: 03/21/10

Programmable Gain Amplifier PGA64 Operating Manual

The Multi Channel Systems device PGA64 amplifies analog signals with the option to change the gain. The input signal amplitude can be increased from a factor of 10 up to 5000. The gain is selectable by software and can be set for each of the 64 signal channels individually. The main parts consist of the analog filter stages, of a logic part to set the amplification, of an EEPROM to save the potentiometer settings, of a level converter accepting RS232 signals and of a power stage.

The signals of the 32 input channels are splitted to two different frequency bands. These bands filter the signals according to their frequency parts. The outputs are observable on the output connector. Examples of output signals are given. Two figures in the appendix demonstrate the dependance of the output signal amplitude from the frequency for the two used frequency bands.

Input signals are connected using a 68-pin SCSI connector. Output signals are transfered to other devices using a 68-pin SCSI connector, too. The pin layout of both connectors is given in a table. The digital signals to change the gain are delivered using a 9-pin SUB-D connector via the serial interface of a PC.

An internal power supply stage transforms the input voltages of any external power supply bin into the supply voltages of ±3.0 V and ±5.0 V. The supply bin should deliver raw voltages of ± 6.5 V at least, for connecting use 2 mm-connectors. The PGA64 uses a 3-pin LEMOSA connector as power supply input connector. The cable will be also delivered, too.

Get pdf Programmable Gain Amplifier PGA64 Operating Manual

AC1 Access Control Equipment Installation Manual

This manual is intended as a help to the physical equipment installation of a Miantek AC1 Access Control System. It contains everything needed to complete an installation, except for the final software commissioning which can be found in the AC1 software help file accessible from within the software through the Help menu item or by selecting START|PROGRAMS|AC1|AC1 HELP from the Windows Taskbar after having installed the software.

The system consists of a PC with Software and a Moxa RS485 bus driver card, one or more C484 controllers, proximity card readers, inputs (ex. door monitors) and outputs (ex. door locks), an example of which is shown in Fig. 1 (Inputs/Outputs not shown).

All communications uses 2-Wire RS485 protocol (between PC and C484’s as well as between C484’s and card readers). It is thus important to use only twisted pair for the communications cables (Ex.CAT5). It is further recommended to use screened cable as far as possible, especially if the runs are very long or if you run the cables near power cables, which you should try to avoid. In theory the communication cables can be up to 1.2km in distance if the proper cable is used. Note that only two wires (1 pair) are needed for the communication and that the wires used MUST form part of the same twisted pair.

The Moxa bus driver card, which should be installed in the PC, may contain two, four or eight communications ports, depending on the size of the overall system. Each port can control up to 32 C484’s, while each C484 can control up to 4 Nortech proximity readers. Only a two-port bus driver card is thus needed for systems of up to 256 card readers (2 ports x 32 C484’s x 4 readers). You may choose to have more communication lines to the controllers in any case and thus rather use a 4 or 8 port card if the installation requires it.

Get pdf AC1 Access Control Equipment Installation Manual

Planar PR6020 DLP Projector Product Manual

Congratulations and Thank You for choosing the PR6020 projector. This product is a XGA single chip DLP® projector.
Outstanding features include:
- True XGA, 1024 x 768 addressable pixels
- Texas Instruments Single chip DLP® Technology
- NTSC/NTSC4.43/PAL/PAL-M/PAL-N/SECAM and HDTV compatible (480i/p, 576i/p, 720p, 1080i)
- Multi-Auto functions: Auto detection, Automatic saving of user adjustments
- IR remote control with laser pointer
- User friendly multilingual on screen menu
- Advanced digital keystone correction and high quality full screen image re-scaling
- User friendly control panel
- One built-in speaker
- UXGA, SXGA+, SXGA compression and SVGA, VGA resizing
- Mac compatible

Powering On the Projector
1. Remove the lens cap.
2. Ensure that the power cord and signal cable are securely connected. The Power LED will flash green.
3. Turn on the lamp by pressing “Power” button on the control panel and the Power LED will turn green.
4. Turn on your source (computer, notebook, video player, etc.). The projector will detect your source automatically within “Management” menu; check that “Source Lock” has been set to “Off”.
- If you connect multiple sources at the same time, use the “Source” button on the control panel or on remote control to switch.

Get pdf Planar PR6020 DLP Projector Product Manual

Puma Hardware Manual

This document explains how to install the Puma Reader. You will understand how to program various parameters of the Puma Reader. Also this documentation explains the core components used in the device and how to “Quick Service” the Reader, if required.

Setting up the Reader:
Connect the 6 PIN RJ-11 attached to the Power Adapter to the Puma Reader.
Connect the 9 PIN Female connector to the PC Serial Port for connecting the Puma Reader with RS232 Communication protocol.
Connect Ethernet (TCP/IP) cable to the Puma Reader. Ensure the other end of Ethernet cable is connected to the Hub / Switch.
Plug in the Power Adapter to AC input€
Now the system is powered and LED Display is active & you hear beep sound.

Assigning IN/OUT Function in Puma Reader:
Assigning Always IN – For Puma Reader
Select Reader Type as “IN” while configuring the Reader in PC Interface Software
Assigning Always OUT – For Puma Reader
Select Reader Type as “OUT” while configuring the Reader in PC Interface Software
Assigning No IN/OUT for Puma Reader
Select Reader Type as “BOTH” while configuring the Reader in PC Interface Software
Assigning User Selectable Type for Puma Reader – is same as Always IN
Select Reader Type as “USER” while configuring the Reader in PC Interface Software. When this option is selected, it is always marked as “IN”

Get pdf Puma Hardware Manual

Signamax 098-2000SX Gigabit Fiber Ethernet Adapter

This manual describes how to install and use the Signamax 098- 2000SX Gigabit Fiber Ethernet Adapter, a high-performance network interface card for 32 and 64 bit PCI buses. Delivering a fully scalable solution, this adapter fully complies with IEEE802.3z 1000BaseSX/LX standards, and auto-negotiates duplex modes. There are more enhanced features added to this adapter, and it certainly satisfies the demands of today’s high-end servers and workstations.

To get the most out of this manual, you should have an understanding of Ethernet networking concepts.

In this manual, you will find:
• Introduction on the Signamax 098-2000SX Gigabit Fiber Adapter
• Product features
• LEDs functions
• Installation instructions
• Specifications

Get pdf Signamax 098-2000SX Gigabit Fiber Ethernet Adapter

PKB-065/078/111/118 Programmable POS Keyboard User Manual

65/78/111/118 keys programmable keyboard with mechanical stroke using full-height Cherry key-switch
True keyboard wedge function; operating with or without the normal pc keyboard
With internal metal plate for key fixation, better to protect against ESD
Multi-Layer programming capability
No TSR program required; avoids application software crashes
Character sets supports: - All alphanumeric characters
- 12 functions keys
- All IBM keyboard special keys (Shift, Ctrl, Alt, Esc etc.)
- 255 ASCII codes

Selectable program mode in ASCII code or SCAN code Each key can be programmed up to 255 bytes, depending on the size of the built-in non-volatile memory Can be cascaded with a normal PC keyboard, barcode interfaced or magnetic card reader through the built-in PS/2 port Each key can be programmed as either strings or single letter key-assignment.

Get pdf PKB-065/078/111/118 Programmable POS Keyboard User Manual

Advanced 7.1 Channel PCI Sound Card User Manual

Sondigo Inferno Advanced 7.1 Channel Sound Card — featuring the most complete set of audio technologies ever assembled in a single sound card product. Powered by the C-Media Oxygen HD PCI Audio Processor, the Sondigo Inferno is the best way to enjoy music, movies and games on your PC. The C-Media Oxygen HD chip is the heart of the Sondigo Inferno and is the latest all digital design from market leaders C-Media Electronics.

Dolby Digital Live enables a single digital cable connection to carry high quality Dolby Digital 5.1 audio from your PC to digital speakers and AV Receivers. All audio, including games and music is processed in real time into industry standard Dolby Digital 5.1 surround.

Dolby Headphone
Dolby Headphone creates a stunning multichannel surround experience over ordinary stereo headphones. Dolby Headphone is compatible with all types of audio on your PC and is so realistic you will believe you are listening over speakers in a well controlled listening room.

Dolby® Virtual Speaker technology simulates a highly realistic 5.1- speaker surround sound listening environment from as few as two speakers. Dolby Virtual Speaker technology also creates a wider two-channel environment during playback of stereo CDs and MP3 content, and when combined with Dolby Pro Logic® II processing, delivers a virtual surround listening experience from any high-quality stereo source.

Dolby® Pro Logic® II technology processes stereo movie and music content into five playback channels of full-bandwidth surround sound. Dolby Pro Logic II unlocks the directional cues that occur naturally in stereo content and processes these elements to create a five-channel surround sound playback experience.

Pro Logic IIx is the first and only technology to process any native stereo or 5.1 signal into a 6.1- or 7.1- channel output, creating a seamless, natural surround soundfield that immerses you in the entertainment experience. With Dolby Pro Logic IIx you can choose Movie or Music modes to tailor your listening experience to source material

DTS-Interactive provides a single cable connection to your DTS enabled surround sound system. Your stereo or multichannel (up to 5.1) audio sources are re-encoded into a DTS audio signal and sent out from your PC to any DTS enabled system such as, powered PC speakers with built-in DTS decoder, an A/V receiver or any other DTS compatible surround sound system. The result: simplified installation, the elimination of the clutter, tangles, and cost of multiple analog cables and high-quality DTS surround sound.

With DTS Neo:PC, you can turn your stereo audio (WMA, MP3, CD, and more!) into a convincing multichannel audio experience. Borrowing from DTS’ Neo:6, the technology that provides you with surround sound from stereo sources in high-end home theatre products, Neo:PC is optimized for your personal computer and is the perfect companion to DTS-Interactive. Now you can upgrade your stereo audio to enveloping DTS surround sound and utilize the single wire solution of DTS Interactive.

Get pdf Advanced 7.1 Channel PCI Sound Card User Manual

MSR 120D SERIES Magnetic Stripe Card Reader USB Interface

The MSR120D USB Magnetic Card Reader series is ideal for retail systems, time keeping systems, security systems and other card reader related systems. The MSR120D series are designed to offer the user a card reader solution that will complement many applications. Triple track of MSR120D is uniquely designed to read both credit cards and Driver Licenses (AAMVA and California standard).

FEATURES
Compact size - can be mounted on keyboard or any flat surface
Software and hardware modification not required
Single, dual and triple track decoding
Bi-directional card swipe and read capability
Audible response for good read “1 beep”, missing data “2 beeps” and non-successful read “3 beeps”
LED indications, LED Off: sending card data; Green: stand-by/good read; Yellow: missing data; Red: error
Baud rate: 9600 (fixed)
Firmware download

Get pdf MSR 120D SERIES Magnetic Stripe Card Reader USB Interface

AHK3000-E Keyboard Manual

The AHK3000-E is a keyboard specifically designed for the use by Equities and Fixed Income traders and is based on the same generic style as the AHK3000-D, eliminating the Dealing 3000 specific keys and adding an LED for indication of sharing status. The AHK3000-E has a number of keys which can be set to record user definable macros. Macros can be up to 64 keystrokes in length.
The AHK3000-E also has digital audio controls and built-in speakers.

The AHK3000-E may be connected directly to a PC or workstation. It also fully integrates with the Amulet Hotkey switches, such as the Amulet Hotkey K4u. Each of these devices supplies the necessary power to the keyboard.

Controls & Status LEDs
A - The AHK3000-E is fitted with two status LEDs. The upper LED is not normally used and will only light in the unlikely event of an internal error condition occurring.
B - The lower of these indicates the sharing status of the keyboard when used with a PC KVM sharer or switch, such as the Amulet Hotkey K4u. In this scenario, the LED will light green if access to the PC is switched to this keyboard.
C - A standard USB input for connection of a mouse.
D - The firmware upgrade port is used to connect the keyboard to a PC for upgrading firmware and keycode sets.
E - Keyboard USB and audio input cable.
F - The general purpose stereo audio output connector which can support either headphones or self powered.

Get pdf AHK3000-E Keyboard Manual

OMT601 Reader User’s Manual

OMT601 Reader can analog USB keyboard to output its detected card number in Win2000\XP\2003\VISTA\WinCE or LINUX operation system, and its interface compliant with USB2.0 HID. The card number can be in decimal or duodecimal by configuring DIP power switch; the card number sequence can be positive-turn or opposite-turn, besides, when read out the card number, users can select with enter function or not.

This product is developed and well-tested by Omni-tech Electronic Co.,Ltd, which can read card UID compliant with ISO14443 Type A. If you want to read Card compliant with ISO14443 Type B or ISO15693, Or these cards data, please contact our company to upgrade the reader.

Features:
1. Built-in transceiver antenna;
2. Maximum effective distance up to 90mm;
3. Less than 200ms decoding time;
4. Low power dissipation and no external power required;
5. Supports USB1. 1 keyboard emulation interface, which compliant with USD2.0 HID.

Get pdf OMT601 Reader User’s Manual

Bluetooth GPS Receiver OnCourse BT-339 User Manual

The OnCourse BT-339 is a GPS receiver with Bluetooth interface and built-in active antenna for high sensitivity to tracking signal. Based on the SiRF star III Low power chip set and supports all functions (Single Sat updates in reduced visibility, Superior urban canyon performance, FoliageLock for weak signal tracking, etc.). The OnCourse BT-339 is well suited to system integrations including PDA, Smart phone, Tablet PC and Notebook PC with Bluetooth devices. It satisfies a wide variety of applications that are purposes in automotive, and outdoor recreation navigation systems.

Before you start up, make sure that your package includes following items. If any item is missing or damaged, please contact your dealer immediately.
Bluetooth GPS Receiver
A CD with the User Manual and the Testing Program.
DC Car Power Charger
GPS Carrying Pouch Case with integrated belt-clip
Optional Accessory : Travel charge adapter

Get pdf Bluetooth GPS Receiver OnCourse BT-339 User Manual

PC-425 User’s Manual

The PC–425 is a compact, single–board computer that is a complete PC based control and data acquisition system. Using a 486SLC processor, the PC–425 is a high performance, low cost solution for an industrial, embedded PC. It will interface with existing PC, Opto MUX, Pro Mux, Micro DAC and uMac systems. The PC–425 is programmable in any PC language, including C, QuickBASIC, and ladder logic.

The PC–425 can be connected in a low–cost network with up to 32 other PC–425s to control 1,024 points. The network communicates at up to 115 KBaud. The points may be digital I/O; high voltage AC/DC I/O; or analog I/O like thermocouples and 4–20 mA outputs.

MAJOR FEATURES
ROM–DOS Operating System
The PC–425 is an “instant DOS” system. The card includes 5.0 compatible DOS in a solid–state disk. If you wish to use your own operating system, you may install it with your application. The system boots and operates the same way as your desktop PC.

COM1 and COM2 Serial Ports
Both serial ports are 16450 compatible. The baud rates are programmable to 115 KBaud. Both have jumperable RS–232/422/485 interfaces. LEDs indicate transmit–and–receive activity. Both ports operate in half and full duplex. The RS–422/485 port on COM1 is opto–isolated with a 500V rating.

On–card Opto Module Rack
The eight position on–card opto module rack accepts both digital and analog I/O modules. The digital and analog I/O can be expanded to 32 lines by connecting an MPC–24 opto rack. Lines can be programmed as inputs or outputs in groups of four and eight. Sixteen of the 24 I/O lines can also drive external devices that require up to 100 mA per device and up to a 50V power supply. Thus, relays, small motors, displays, and other devices can be driven directly by the system. The outputs act as switches…

Get pdf PC-425 User’s Manual

Mvix Nubbin (MS-811N) User Manual

Mvix Nubbin (MS-811N) is an IEEE802.11b/g/n mini-size USB adapter that can connect notebook, handheld or desktop PC equipped with USB2.0 interface to a wireless-N network. It brings the freedom of staying connected to the network at blazing-fast Wireless-N speeds while maintaining access to the Internet, e-mail, networked applications, and print services. The “nubbin” is a perfect companion for your notebook providing access to the internet-enabled world anytime - anywhere.

The MS-811N fully complies with IEEE 802.11n draft 3.0 and IEEE 802.11 b/g standards, delivering reliable, cost-effective, feature rich, wireless connectivity at high throughput from an extended distance. It supports WMM and WMM-PS (IEEE802.11e QoS standard) and has an innovative, built-in, WPS (Wi-Fi Protected Setup) feature which auto-builds a connection between the wireless router (access-point).

Features:
• USB2.0 Wireless-N (150Mbps) Adapter
• Mini-footprint, Protrusion: Less than 2cm
• Compliance: IEEE 802.1n draft 3.0, IEEE 802.1b/g
• Supports WMM and WMM-PS (IEEE 802.1e QoS Standard)
• Innovative WPS (Wi-Fi Protected Setup) - auto-builds connection, synchronizes settings.
• Reliable, cost-effective, wireless connectivity at high throughput.

Get pdf Mvix Nubbin (MS-811N) User Manual

Video Splitter 2/4/8 PORTS User’s Manual

The Video Splitter takes the computer’s video signal and displays it on up to 2/4/8 analog monitors. The same image is displayed in all monitors. The Splitter provide fast, flexible, solutions for Test Bench Facilities, Data Centers, or video broadcasting such as Remote Monitoring, Presentations, Educational Facilities, Stock Quotes, etc…

FEATURES
1. Supports ULTRA HIGH 350 MHz video (-3dB) bandwidth.(only Video Splitter with 350MHz)
2. Supports ULTRA HIGH 200 MHz video (-3dB) bandwidth.(only Video Splitter with 200MHz)
3. Enhances video signals for distance up to 65M
4. The video splitter can be daisy chain
5. All metal casing
6. Small form factor
7. Supports 2048X1536 at 60Hz(only Video Splitter with 350MHz)
8. Supports 1600X1200 at 75Hz(only Video Splitter with 200MHz)
9. Ideal for video broadcasting: remote monitoring, presentations, educational facilities.
10. The video splitter has locking connector for cables.
11. Allows one computer to provide simultaneous displays on 2/4/8 different monitors.

Get pdf Video Splitter 2/4/8 PORTS User’s Manual

AEC-6810 Embedded Control PC User Manual

The AEC-6810 Embedded Control PC is the smallest, highest-performance, multi-functions model among the all products in the current market with same level and orientation. The tough vibration test has been certificated. Even if the model is under the environment with long-term vibration and shock, it is bearable and can keep the system operation stable. Beside, the anti-vibration HDD device can be applied in the machine with high vibration frequency.

The compact size model offers the end user more flexibilities and alternatives for system integration and arrangement. The system supports various operation systems such as Windows CE.NET 4.2, Windows XP Embedded and normal Windows family. The 4 serial ports support can provide the applications to the industrial automation in the plant. The multi-media function with TV audio output and AC97 also give the user creativity and innovation to apply the feature fully in the related field.

The market mainstream will be focused on industrial domination field where Internet and I/O communication transmission application involved. And otherwise the targets on transportation, environment and industrial facility monitoring will be spread comprehensively and widely over Building Automation, ATM, KIOSK and relevant IPC boundaries.

Get pdf AEC-6810 Embedded Control PC User Manual

Druid Electric Fence Energizer Installer Manual

The DRUID is a battery (12V 7AH nominal) operated energizer suitable for connection to mains (230V 50Hz nominal). The batteries to be used are rechargeable lead-acid batteries. Non-rechargeable batteries must NOT be used. The lead-acid batteries require venting and it is imperative that the energizer be situated in a well-ventilated area.

Mounting / Battery Replacement Procedures
STEP 1: Disconnect mains. Open the lid by removing the two cap screws. Unplug the battery terminals if connected.
STEP 2: Remove screws and battery bracket
STEP 3: Remove battery
*Dispose of old battery according to legal requirements.
Do NOT replace with non-rechargeable battery!!
STEP 4: Drill 4 x 8mm holes for mounting the unit, use the template provided with the unit. Four nail-in anchors are also supplied with the unit. Insert the plastic sleeve of the nail-in anchor from the inside of the box and then hammer the screw in with a screw driver and hammer.
NB: Always insert the plastic sleeve from the inside of the box.
STEP 5: Insert battery with the positive terminal to the top.
STEP 6: Place the battery bracket back (with plastic offsets at the top) and fasten the screws.
STEP 7: Connect battery wires. Close the lid by hooking the top of the lid in first and then fasten the bottom down with the two cap screws. Apply mains to the unit.

Get pdf Druid Electric Fence Energizer Installer Manual

TS-NVRAM2 Manual

The TS-NVRAM2 is a PC/104 expansion card that adds up to 2 MB of nonvolatile high-speed battery-backed RAM. It can be arranged as 8 bit or 16 bit wide memory and can be configured as paged memory or linear memory. The TS-NVRAM2 eliminates any wear-out failure and write cycle latency inherent in all Flash devices This product uses a multi-layer PCB with power and ground planes to minimize noise and EMI issues. The TS-NVRAM2 only requires a single 5V power supply.

Getting Started X86 Architecture
Install only jumpers 3 and 4 on the TS-NVRAM2, this will put the board in 8-bit mode and set the base address for all registers in the I/O space at 0×140. After a system reset, only the eight I/O registers will appear on the PC/104 bus (no memory range will be decoded) — this will avoid any conflicts with any other devices. Next write out 0×46 to I/O location 0×145 (Mode Register). This will configure the TS-NVRAM2 to use paged memory and will make it appear in memory space at 0xD0000 to 0xD7FFF (a 32 KB window). This memory range is suggested, since this range is typically free in most x86 platforms, but any 32KB range from 0xA0000 thru 0xDFFFF can be selected (see Mode register details). Now the NVRAM memory can be accessed at the memory addresses 0xD0000 to 0xD7FFF. Any one of the 64 pages can be selected by writing to the page register at I/O location 0×144. Since each page is 32 KB and there are 64 pages this allows access to all 2MB of NVRAM. Up to four TS-NVRAM boards can be installed to get up to 8MB of non-volatile memory.

Get pdf TS-NVRAM2 Manual

XSV Board V1.1 Manual

The XSV Board brings you the power of the XILINX Virtex FPGA embedded in a framework for processing video and audio signals. The XSV Board has a single Virtex FPGA from 50K to 800K gates in size. The XSV can digitize PAL, SECAM, or NTSC video with up to 9-bits of resolution on the red, green, and blue channels and can output video images through a 110 MHz, 24-bit RAMDAC. The XSV can also process stereo audio signals with up to 20 bits of resolution and a bandwidth of 50 KHz. Two independent banks of 512K x 16 SRAM are provided for local buffering of signals and data.

The XSV Board has a variety of interfaces for communicating with the outside world: parallel and serial ports, Xchecker cable, a USB port, PS/2 mouse and keyboard port, and 10/100 Ethernet PHY layer interface. There are also two independent expansion ports, each with 38 general-purpose I/O pins connected directly to the Virtex FPGA. You can configure the XSV Board through a PC parallel port, serial port, Xchecker cable or from a bitstream stored in the 16 Mbit Flash RAM. The Flash RAM can also store data for use by the FPGA after configuration is complete.

Get pdf XSV Board V1.1 Manual

Remote Satellite Data Module RST600 Installation and User Manual

The RST600 is a Remote Satellite Data Only Module designed to provide a reliable and cost effective data service connection when a wired connection is not available. It does this by providing a standard interface to the Iridium network — a satellite-based, wireless communications network that enables remote communication. The RST600 allows the connection of standard data terminals and other telecommunications devices.

The RST600 from Beam Communications brings you all the convenience and ease of use of a Data Service anywhere in the world using the Iridium Satellite system. The data services available on the RST600 terminal include
• Circuit Switched Data
• Short Message Service (SMS)
• Short Burst Data (SBD)

The RST600 package contains:
1 x RST600 Data & Power Interface cable assembly
1 x Iridium L-Band Transceiver
1 x RST997 DC – DC converter to supply 4.4VDC to the transceiver
1 x Cable Assembly for RST997 DC power supply
1 x User manual in hard copy
1 x Beam Starter CD including AT command set

Get pdf Remote Satellite Data Module RST600 Installation and User Manual

H-ITT RX4000 instruction manual

The RX4000 communicates with all H-ITT RF clickers. There is no limit to the number of RF clickers that can be used with the RX4000. The RX4000 has 31 RF channels that can be selected and are provided so that a classroom may have a unique RF channel to avoid interference between another device in or about the classroom. The RX4000 is initially set to channel 07 to operate with H-ITT RF clickers that are also initially set to channel 07. The RX4000 has selectable baud rates for communication to your PC. The default setting is 19.2K baud. Higher Baud rates are available, but typically not needed. If higher baud rates are selected, the length of the USB cable should not exceed 15 feet. There can be more than one RX4000 installed in a very large classroom or auditorium to provide reliable communication with H-ITT’s remote clickers.

INITIAL SET-UP:
The RX4000 provides both USB and Serial communications ports. Connect either of these ports to your classroom PC (do not connect both). The USB connection provides power to the unit, so this is the only connection needed. You will need to install a driver for the USB port in your PC to communicate with H-ITT software (see below for connecting to a computer). However, the RX4000 will power up as indicated below with or without the drivers installed.

Attach the antenna to the SMA connector.
Power up the RX4000 by connecting the USB cable to a PC (that is powered up) or connect the external power supply to the DC power jack. The YELLOW indicator light will turn on and both the GREEN PC com and RED RF com indicators will blink 4 times each. If the RF com indicator blinks more than 4 times, and at a rapid rate, this can indicate that the RF channel selected may have another fixed frequency transmitter operating on the same channel within the range of the base. If this occurs, it is recommended that a different channel be selected using the internal set-up switch described below.

Get pdf H-ITT RX4000 instruction manual

OpenVox B200P/B200E/B400P/B400E User Manual for mISDN v2

B200P/B400P series is a PCI 2.2 compliant card supporting 2 or 4 BRI S/T interfaces, with an onboard multi NT power feeding circuit. NT/TE mode can be independently configured on each of 2 or 4 ports. B200P/B400P series can be implemented for building Open Source Asterisk based systems such as ISDN PBX and VoIP gateway.

Target Applications:
High Performance ISDN PC Cards
ISDN PABX for BRI
VoIP Gateways
ISDN LAN Routers for BRI
ISDN Least Cost Routers for BRI
ISDN Test Equipment for BRI

Main Features:
Four integrated S/T interfaces
ITU-T I.430 and TBR 3 certified and S/T ISDN supporting in TE and NT mode
Integrated PCI bus interface (Spec.2.2) for 3.3V and 5V signal environments
DTMF detection on all B-channels
Multiparty audio conferences bridge
Onboard power feeding
PCM bus connectors daisy chaining
Each of the 2 or 4 ports can be independently configured for TE or NE mode
Full software and hardware compatible with Junghanns.NET ISDN and mISDN driver
Application ready: ｕse Asterisk to build your IP-PBX/Voicemail syste

Get pdf OpenVox B200P/B200E/B400P/B400E User Manual for mISDN v2

MADASS Operating Manual & Installation Guide

The MADASS, Monitoring And Data Acquisition Storage System, is a vehicular data recording device designed to record relevant vehicle operating parameters before and after the occurrence of an incident, defined as an event where lateral or axial acceleration has exceeded pre-defined G force limits.

Lateral and axial acceleration are monitored continuously until an incident occurs. Once an incident occurs the MADASS stores the data from 120 seconds before and 15 seconds after the event. A battery backup system ensures the MADASS will continue to record even if vehicle power is not available after the incident has occurred.

The complete system consists of:
- The MADASS main recording system which records the 3 signals from the LG-Alert, as well as pertinent vehicle operating data including engine RPM, throttle position, steering wheel position, brake system pressure, brake position and vehicle position (longitude, latitude), course and speed from a GPS receiver.
- The LG-Alert unit, which provides lateral, axial, and vertical acceleration signals to the MADASS system.
- A remote display unit which displays current operating status, system diagnostic information, and the number of stored incidents. It also provides a communication port for a PC to download incident data for analysis.
- GPS antenna
- Steering wheel position sensor
- Brake air pressure sensor

The system records data continuously while the vehicle master power is turned on. Once an incident occurs all data is stored in non-volatile memory. A total of 5 incident records are stored in the MADASS unit for retrieval and analysis. If the total number of stored incidents exceeds five the next incident overwrites the data of the previous incident in the order of 1 to 5.

Get pdf MADASS Operating Manual & Installation Guide

CP-3160RD/3320RD Deluxe DVR Board Hardware Manual

This section details the installation of your CP-3160RD Deluxe DVR board and how to make the necessary connections. You may install another Daughter Card (CP-1605RD) into a PC to reach 32 Video input. The primary one is referred as CP-3160RD Deluxe 0, the other one will be called CP-1605RD Daughter card. Before you start, please make sure that your PC is off, and the power cable is unplugged. The DVR system is called CP-3320RD Deluxe when combine the CP-3160RD Deluxe 0 and CP-1605RD Daughter card together. The CP-3320RD Deluxe can supports 32 video input.

The description of CP-3160RD Deluxe 0 (Fig1) and CP-1605RD Daughter Card (Fig1-1) pins and sockets:
1: DB 25 – Video input.
2: TV out – S connector for split video and single Video output
3: Video looping- Connect to a video looping board for video loop-out.
4: 40 Pin (2×20) male connector – Connect to the 1605RD Daughter Card to make 32 channels video input.
5: EM_B – Panic button socket (CP-3160RD Deluxe 0 only)
6: RESET- System failure socket, connect to the “ Reset “ socket of PC Motherboard. (CP-3160RD Deluxe 0)
7: LED – The indicator of auto reboots function.
8: Sensor connector-Connect to the sensor cable of the remote controller. (CP-3160RD Deluxe 0 only)
9: Audio in - Connect to an audio board for audio input. (CP-3160RD Deluxe 0 only)
10: J_USB – Connect to USB cable to the internal USB port of PC Motherboard.
11: Jump– DVR card number selection (A reserved function).
12: 4 Pin power socket – The socket for power input from power supply of the PC. (CP-1605RD only)

Get pdf CP-3160RD/3320RD Deluxe DVR Board Hardware Manual

HP Jornada 700 Series Handheld PC User’s Guide

Congratulations on purchasing the Hewlett-Packard Jornada 700 Series Handheld PC (H/PC), a mobile device powered by the Microsoft® Windows® for Handheld PC (H/PC) 2000 operating system. The size and capabilities of the HP Jornada H/PC let you keep your most important business and personal information current and close at hand. Your HP Jornada supports the latest version of Microsoft Pocket Outlook, so you can check e-mail and manage your appointments and contacts while on the road.

Your HP Jornada is also the perfect companion to your desktop or notebook PC. It allows you to take vital business data and documents with you when away from the office, then easily transfer updated information back to your PC upon return. A powerful, reliable, mobile business partner, HP Jornada offers you the highest quality in performance and battery life as well as rich programs and utilities designed by Hewlett-Packard. If you are familiar with Microsoft Windows products and notebook PCs, you will notice that your HP Jornada has many of the same characteristics, making it easy for you to be productive quickly.

In this chapter, you will find:
• An overview of this User’s Guide and other sources of help and information
• A list and brief descriptions of the built-in applications, including MS Windows for H/PC 2000 software and special HP applications
• An introduction to HP Jornada features and a description of the advantages of using the HP Jornada.

Get pdf HP Jornada 700 Series Handheld PC User’s Guide

BF-100C USB File Transfer Cable User’s Manual

Congratulations on your purchase of the PC-Linq, an USB file transfer cable. This unique cable allows you to easily connect two computers with USB port and instantly transfer files at great speed. The PC-Linq USB cable is your fast solution for peer-to-peer file transfer between two computers via the USB port. The cable provides true plug-and-play capability while transferring files at much greater speed than traditional file transfer products via serial or parallel port, up to 6M bits/sec can be achieved. PC-Linq application program, a Windows® Explorer-like user interface, provides drag-and-drop user-friendly interface to transfer files. You simply plug in the PC-Linq cable and install the application software into your PC.

Product Features
USB specification revision 1.1 compliant
Single cable solution for files transfer, High-speed data transfer rate up to 6M bits per second
Drag-and-drop user-friendly interface. Includes print function for remote files, power management and remote wake-up functions

Get pdf BF-100C USB File Transfer Cable User’s Manual

Ampeg SVX Installation Manual

Ampeg SVX must be authorized to work with unrestricted functionality. It will run with full features for 10 days (grace period) which will start when launched for the first time, and revert to demo mode after. You will need to authorize the product within this time frame to enable permanent unrestricted functionality.

To authorize your Ampeg SVX you’ll need three numbers:
- Serial Number: this is contained on a card in the license envelope.
- Digital ID: this will be shown during the authorization process and linked to the hardware where you are running the software.
- Authorization Code: this will be generated online by registering and inserting the Serial Number and Digital ID. If you are a registered IK Multimedia user, having your User ID and Password on hand, will help speed up the authorization process.

A built in software Wizard helps you in the authorization of your IK software. The first time the software is launched the Wizard is displayed (Step 1. Wizard Introduction). Click Cancel to return to the software and use the software within the 10 days grace period. Click Next to go to the Wizard’s next Step and authorize the software.

Get pdf Ampeg SVX Installation Manual

DPA III+ ISA -or- DPA III+ PC/104 Quick Start Guide

This guide explains basic DPA product installation. Refer to the manual on the installation CD for more details. The DPA package includes a DG Installation CD-ROM with the driver files necessary to use this product. You may need to install OEM software packages (diagnostic or otherwise).

The DPA unit needs the following PC hardware for operation:
• AT-compatible computer (or higher)
• Interrupt 5, 7, or 10 available
• I/O Address Range 200, 220, 300, or 320 available
• PC/104 hardware needs a free PC/104 Bus Slot
• ISA hardware needs a free ISA Bus Slot

To configure the DPA:
The DPA III ISA and PC/104 card uses jumpers to set the resources (IRQ and Base Address) that it will use. The DPA supports four base address choices and three IRQ selections, as defined in the section above (Information is printed on the ISA card for simple configuration.) Selecting the Interrupt and I/O Address Range for your hardware: Before installing the DPA PC/104 card, it is important to check your PC’s current configuration to identify an unused IRQ and address region. In Windows 95 or Windows 98, you may identify these regions using the device manager. In Windows NT, you may check the current configuration using the WINMSD.EXE program

Get pdf DPA III+ ISA -or- DPA III+ PC/104 Quick Start Guide

PC/HD With Audio to HDMI Format Converter Operation Manual

The PC/HD to HDMI format conveter converts analog PC RGBHV/YPbPr and audio signal to digital HDMI format. It allows you to connect the analog HD-15 RGBHV/YPbPr output from PC or Video equipments to the digital HDMI input of the latest HD ready plasma,LCD or DLP TV. Its high bandwidth capability supports a wide range of PC and HDTV resolutions.

Features:
* It enables you to connects computers with analog PC output or DVDs with YPbPr output to HDMI input of HD ready plasma, LCD or DLP TV.
* You can select input format as PC/RGBHV or HD/YPbPr.
* HDMI is compliant with HDMI 1.2
* Supports up to 1600 x 1200 @ 60 for PC input and 1920 x 1080p @ 60 for HD input

Get pdf PC/HD With Audio to HDMI Format Converter Operation Manual

MSR1000 SERIES Magnetic Stripe Card Reader USB Interface Simple Manual

MSR1000 is a USB interface magnetic card reader with basic features to provide magnetic stripe card data decoding with raw data output to host (PC). With a relevant API package, user can decode the desired data format by appreciated API.

FEATURES
- Single, dual, or triple track versions allow to reading ISO7810/7811, AAMVA and DMV cards.
- Raw data output.
- Provide a DLL package for decoding the raw data to appropriate format for the AP at terminal/host.
- Compact size without bottom cover and it can be mounted on keyboard or any flat surface.
- Power supplied from USB port of host system.
- Optional LED to indicate the status of reader

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio / TV technician for help

Get pdf MSR1000 SERIES Magnetic Stripe Card Reader USB Interface Simple Manual

SANYO Software Pack 7.8 For Digital Movie Camera Installation Manual

This manual describes how to install and operate the SANYO Software Pack. Please read this manual carefully, in order to use the images and audio recordings captured with your camera in a wide range of applications.

About this manual
The explanations in this manual conform to the following conventions. The examples given in this manual are generally based on a Windows environment. For Macintosh users, while the menu names and screen indications may be different, this is no impediment to understanding the operation. In those places where the operations for Macintosh users and Windows users differ, specific explanations are provided.

In this manual, the SD Memory Card is referred to as “card”.
- This manual is designed for users with the following computer skills:
- Knowledge of basic computer operations
- Knowledge of basic mouse operations
- Knowledge of how to open, close, move, minimize and maximize windows
- Knowledge of how to move from one folder to another folder Detailed information about the operations listed above can be found in the printed or online manuals accompanying the computer or operating system software.

Get pdf SANYO Software Pack 7.8 For Digital Movie Camera Installation Manual

M-Audio AudioBuddy Users Manual

Thank you for your purchase of the M-Audio AudioBuddy™, mic preamp and direct box. M-Audio has designed and manufactured several different audio mixers including MiniMixer, MicroMixer 18, MultiMixer 6, MultiMixer 10 and miXim 10. All of these mixers have two things in common: 1.) they are exceedingly quiet — quieter than 99% of all mixers on the market and 2.) they are uniquely configured to meet the specific needs of the MIDI and multimedia musician.

The Audio Buddy, once again, fits these two criteria. First, it is a very quiet mic preamp. This is because the unit’s simple and efficient design and ultra compact layout eliminates much of the noise. The unit also has a higher than usual voltage “rail” across its internal op-amps. This means that you get more “punch” and much more dynamic audio output. Secondly, the Audio Buddy (when coupled with its ultra quiet performance) is the perfect audio “gateway” for recording the two most significant, non-line level instruments in the studio: microphones and electric guitars.

The Audio Buddy has two completely independent preamplifier sections. Each of these sections has: 1.) a balanced XLR input on the back of the unit, 2.) a high impedance 1/4” unbalanced input (TS) on the front of the unit, 3.) signal (present) and clipping LEDs, 4.) a gain control and 5.) a 1/4” dual purpose output on the back of the unit that provides either an unbalanced out (when a mono plug is used) or a balanced out (when a stereo plug is used).
IMPORTANT:
Whenever one of the front panel high impedance inputs is used, the associated back panel XLR is disabled.

The Audio Buddy also has built in phantom power which can be switched on or off for both channels. When the rear panel phantom power switch is in, phantom power to both channels is turned on and the front Phan(tom) power LED will light.

IMPORTANT:
Since the phantom power switch turns phantom power on or off for both channels, there is no way to turn phantom power on for one channel and off for the other channel. If you are using the high impedance inputs the phantom power switch has no effect.

Get pdf M-Audio AudioBuddy Users Manual

PS3-S201 Play PlayStation ® 3 on a DVI Monitor / LCD TV User Manual

Play PS3 on a DVI monitor is not a dream anymore! GAMESWITCH makes it become reality. It allows you to play PS3 on a regular DVI monitor, plus its switching function, you can either play PS3 or operate PC* in the same monitor. Furthermore, you don’t need to connect PS3 to an expensive LCD TV and display mostly in 1080i; you can play over a DVI monitor and reach 1080p/7 0p resolution to enjoy professional multimedia game. If you are still use traditional TV (480i resolution), GAMESWITCH is your greatest choice, by adding a DVI monitor, you can use the most economic way to enjoy high quality game. Now, enjoy PS3 not only in living room, but also besides your PC!

Key Features
1. Switch one HDMI source (Ex: SONY PlayStation®3) and one DVI displayed PC to one DVI monitor and stereo speaker, Support 480p, 7 0p, 1080i, 1080p
3. Compliant with HDMI1. , HDCP, and DVI1.0
4. Auto and manual channel selection, an external button is attached with the cable connected to monitor
5. Electronic design and high quality signal transmission
6. LED status to indicate the source displayed
7. Magnetic pad and attachable metal plate to ease the installation
System Requirement 1. DVI monitor build in speaker or with an external speaker. PC with DVI output (optional) / Panel Description

Get pdf PS3-S201 Play PlayStation ® 3 on a DVI Monitor / LCD TV User Manual

ADSP-2100 Family EZ-Kit Lite Reference Manual, Getting Started

The EZ-KIT Lite contains the ADSP-2181 EZ-LAB evaluation board, ADSP-2181 Development Software, IBM PC compatible host software, example programs and demos, and documentation. You can obtain additional information and documentation from your local Analog Devices sales office or authorized distributor. You may find this documentation useful if you are planning to do a significant amount of ADSP-2181 code development. The following documents can be obtained or purchased:
ADSP-2100 Family User’s Manual
ADSP-2100 Family Assembler Tools & Simulator Manual
ADSP-2181 User’s Manual

To fully utilize all the functions of the EZ-KIT Lite you will need to install the provided software on to an IBM compatible PC and connect the EZ-KIT Lite board to the PC as well as connect it to a power supply, analog input source and amplified speakers.

This section contains a very brief description of the EZ-KIT Lite software installation procedure. It is written for experienced PC users familiar with installing software onto their PC.

The install utility for the EZ-KIT Lite should be run under Windows™.
1. Make sure Windows is running.
2. Insert EZ-KIT Lite Software disk into a floppy drive. (usually A: or B:)
3. Open the Program Manager window, if it is not already open.
4. From the File menu, select Run. The Run dialog box should appear.
5. In the “Command line” box type A:\SETUP.EXE ( or B:\SETUP.EXE ).
6. Click on OK or press enter.
7. Follow the instructions on the screen.
Note: You will need to edit your AUTOEXEC.BAT file in the following manner.

Get pdf ADSP-2100 Family EZ-Kit Lite Reference Manual, Getting Started

ENLTV-DVB-S DVB-S PCI TV Tuner User’s Guide

Upon receiving your ENLTV-DVB-S, please make sure the following items are included in the ENLTV-DVB-S package.
CD of Installation Software
ENLTV-DVB-S Card
Audio Cable
4 in 1 Audio / Video cable
Remote sensor cable
Remote Controller
User’s Guide or Quick Installation Guide

System Requirements
IBM PC or compatible
PCI 2.1 or 2.2 compliant interface
Intel Pentium IV 2.0GHz CPU or higher (Recommended)
Minimum 256 MB memory
Minimum 1GB hard disk space available
VGA card supports DirectX 9.0c or above
SoundBlaster compatible sound card
One free PCI slot
Microsoft Windows XP Home or Professional with Service Pack 2, Windows Vista
CD-ROM drive for driver and software installation

Connect ENLTV-DVB-S
Notes: Satellite cable has 12V power. At the first time installation, please make sure the PC system’s power cord has not been connected to the power jack even when the PC’s power is in shutdown state. Turn on the PC power ONLY after the ENLTV-DVB-S has been firmly and securely plugged into the PCI slot.

Download pdf ENLTV-DVB-S DVB-S PCI TV Tuner User’s Guide

Miditech Guitarface USB Owner’s Manual

Thank you for deciding to purchase the Miditech Guitarface, we are certain you will be delighted with its performance and advanced features. Guitarface enables you to easily digitize all your analog sound sources from any LINE level devices, e.g. music cassette decks or CD players, etc. With its implemented HI-Z instrument preamp you can easily digitize instruments like electric guitars and basses. At last the integrated MIC preamp offers you the possibility to make microphone recordings. In addition to this Guitarface gives you a switchable phantom power for use with condenser microphones. Please read the instructions to use this phantom power carefully! If you use it in the wrong way, it may cause damage to your speaker system! Miditech doesn’t take any responsibilty for damage caused by improper use!

Not only does Guitarface offer a simple solution to digitizing analogue sounds, it also gives you the very best HiFi audio quality. The included recording software Magix “Samplitude SE” offers you the capability to edit previously digitized music or speech. The software “IK Multimedia Amplitube 2 Duo” gives guitarists some perfect simulated American guitar amps for use as standalone application or as a VST instrument. The operating instructions will give you some guidance on how to install and operate your Guitarface functions, also check the section on how to use the free bundled companion programs - “Magix Samplitude SE” and the amp-simulation from “IK Multimedia Amplitube 2 Duo”.

Get pdf Miditech Guitarface USB Owner’s Manual

PC/HD to DVI Format Converter Operation Manual

The PC/HD to DVI-I format conveter converts analog PC RGBHV/YPbPr signal to digital DVI signal. It allows you to connect the analog HD-15 RGBHV/YPbPr output from your PC or Video equipments to the DVI input of the monitors or projectors. Its high bandwidth capability supports a wide range of PC and HDTV resolutions.

Features:
* It enables you to connect computers with analog PC output or DVDs with analog HD output to digital DVI-I monitors or projectors.
* You can select input between analog RGB and YPbPr.
* You can also select output between Bypass or digital RGB.
* Supports up to 1600 x 1200 @ 60 Hz for PC input and 1920 x 1080p @ 60 Hz for HD input.
* Supports DDWG standard for DVI complaint monitors.

Operation Controls and Functions
1. HD-15 D-Sub input: Connects to the PC or YPbPr output of your PC or YPbPr
source equipment, using VGA cable, or D-Sub to 3 RCA adaptor cable.
2. DC 5V power input jack.
3. Power LED light.
4. DVI-I output: Connects to the DVI input of your display TV through DVI cable.
5. Input format switch:
- Set the switch to YPbPr when the output format of your source equipment is component YPbPr. Use VGA to 3 RCA adaptor cable to connect between your source equipment and the CP-261D.
- Set the switch to RGB when the output format of your source equipment is RGBHV. Use- HD-15 D-Sub VGA cable to connect between your source equipment and the CP-261D.

Get pdf PC/HD to DVI Format Converter Operation Manual

PB-0555 Freescale MPC555 PowerPC Microcontroller Board

The PB-0555 is a Freescale MPC555 PowerPC Microcontroller module with I/O pin headers, oscillator circuit, power supply, and RS232 COM port. The MPC555 high integration processor architecture has been designed for high-performance and low-cost embedded control applications. A version of the PB-0555 can be used on the CME0555 Development Board, in your own application hardware or as a single chip stand alone controller.

Board Features:
• Simple Monitor and CMFI Programmer in MPC555 Flash (self protected)
• Single Chip Operation
• All I/O and Bus to Header Connectors
• 4MHz Reference Crystal Oscillator
• RS232 Level Serial Port
• +7-20V Input Power Supply
• Prototype Area

MPC555 Features:
• Power PC core with Floating Point Unit Processor
• 40MHz Operation, software selectable
• 448K Bytes Flash EEPROM on chip
• 26K Bytes SRAM on chip with battery backup Supply support
• 5V External Interface I/O system with
o 24 address lines, 32 data lines,
o 4 programmable chip selects
• Queued Serial Multi-Channel Module with
o 2 SCI UART channels w/ 16Byte FIFOs,
o Queued Serial Peripheral Interface
• 2 TPU3 Time Processor Units with
o 16 Channels with I/O per Unit
o 9 Pre-programmed functions
• 2 Queued 10Bit Analog to Digital Converters w/Up to 16 input channels each,
o 10us conversion time, 64 result registers,
o Selectable modes and data type

Get pdf PB-0555 Freescale MPC555 PowerPC Microcontroller Board

RMC150 RS232 Ethernet Controller For SE500 Instruction Manual

The Datavideo RMC150 is a remote control box for the SE500. It allows the SE500 to be controlled from a PC via an Ethernet connection.
Features
Ethernet to RS232 remote controller for the Datavideo SE500
LED Ethernet Communication Indicator
Compact design
Built in mounting plate for easy installation
Locking 2.1mm inline DC In socket
12V 300mA power requirement (12V 500mA PSU supplied).

Front Panel
Ethernet Port Connect this to the Ethernet connection of your PC or to a hub. The green LED indicates connection and the yellow LED indicates activity.
N.B. If you are connecting directly to a PC (not via a hub) please use a CAT 5 Crossover Cable (not supplied).
RS232 Port Connect this to your SE500 vision mixer RS232 Control Port, with the supplied cable. Power In Socket Connect the supplied power supply to this socket. Please note the socket is labelled 12v 300mA whereas the power supply is 12V 500mA, this is intentional.

Get pdf RMC150 RS232 Ethernet Controller For SE500 Instruction Manual

R-4 Bulldozer User’s Manual

R-4 ‘Bulldozer’ has two integrated Thermometer sensors and its LED displays are located on the front and side panel. This feature is extremely good for users to monitor the PC hardware temperature according to the location of those sensors. It also has integrated fan speed controller so the users can control the air flow and noise.

Chapter 1. Product Introduction
There are Temperature LED displays and some I/O ports like two audio jacks, 2 USB ports, Power button and Reset button at the bottom of the front panel. On the right front panel, there is an eject button to eject the ODD. The ODD tray panel is supported by two spring steel bar: some sort like shock absorber. There is a tuning effect with 92mm LED and it is an intake fan to provide the fresh air to cool down the hardware inside the case.

Get pdf R-4 Bulldozer User’s Manual

Component Video (RGBHV) Distribution Amplifier 1×2 With Composite Sync. Generator

The Model 210-LP buffers and splits component (RGBHV) video signals for display on two monitors. The unit can
drive special cables up to 150 feet or longer depending on the resolution used and cable quality.
The input video signal can be RGBHV (five connections, separate syncs), or RGBS (four connections, composite
sync), or RGB (three connections, with sync-on-green).
Regardless of the type of the input type, both outputs produce the same signal components on their respective connectors. The device has the added feature of being able to generate composite-sync or sync-on-green outputs from an RGBHV signal such as VGA.

The Model 210-LP can be powered from a supplied power adapter, or from customer supplied +5V DC. This feature is useful for displaying a VGA signal on monitors having 3 or 4 BNC inputs instead of 5. It is also useful for cases where a video switch (such as a Matrix) is to follow the device. Instead of a switching 5 components, only 3 or 4 components need be switched (thereby, lowering the cost of the switch).

When the input is RGBHV (five connections), you can have the unit pass all the data through without modification (”SEP”), combine horizontal and vertical syncs into a (”COMP”), or provide a output (”GRN”). The Model 210-LP automatically generates a composite sync signal with negative going pulses regardless of the polarities of H and V input signals.

Features
• Rugged, Reliable, Economical
• 300 MHz Bandwidth
• Powered from AC source or 5 VDC
• Each output can independently generate composite sync
• LED power indicator
• BNC connectors on input and outputs
• Mounting holes for attachment in user equipment

Get pdf Component Video (RGBHV) Distribution Amplifier 1×2 With Composite Sync. Generator

1T-V1280HD Video-PC/HD Converter Instruction Manual

The 1T-V1280HD is designed to convert Composite or Component Video to a wide variety of PC and HDTV resolutions. Our professional video conversion products have been serving the industry for over twenty years. TV One offers a full line of high quality Video Scalers, Scan Converters, Analog-Digital (DV, SDI, DVI) Converters, Standards Converters, Digital Video Recorders, Frame Synchronizers, Time Base Correctors, LCD Monitors, Matrix Routing Switchers and Distribution Amplifiers.

Before attempting to use this unit, please check the packaging and make certain the following items are contained in the shipping carton:
• 1T-V1280HD Converter
• 100240VAC AC/DC Power Adapter
• Composite Video Input Cable
• 8 Pin Mini-DIN to SCART Adapter
• 6 Ft HD-15M Cable
• User Manual

Note: Please retain the original packing material should the need ever arise to return the unit. If you find any items are missing, contact your reseller or TV One immediately. Have the Model Number, Serial Number and Invoice available for reference when you call.

Get pdf 1T-V1280HD Video-PC/HD Converter Instruction Manual

Super P6DLH/P6DLF Motherboard User’s Manual

This manual is written for system houses, PC technicians and knowledgeable PC end users. It provides information for the installation and use of SUPER P6DLH/P6DLF motherboard. SUPER P6DLH/P6DLF supports Pentium II 233/266/300/333 MHz. The Pentium II processor with the Dual Independent Bus Architecture is housed in a new package technology called the Single Edge Contact (S.E.C.) cartridge. This new cartridge package and its associated “Slot 1″ infrastructure will provide the headroom for future high-performance processors.

Manual Organization
Chapter 1, Introduction, describes the features, specifications and performance of the SUPER P6DLH/P6DLF system board, provides detailed information about the chipset, and offers warranty information.
Refer to Chapter 2, Installation, for instructions on how to install the Pentium II processor, the retention mechanism, and the heat sink support. This chapter provides you with the instructions for handling static-sensitive devices. Read this chapter when you want to install or remove SIMM/DIMM memory modules and to mount the system board in the chassis. Also refer to this chapter to connect the floppy and hard disk drives, IDE interfaces, parallel port, serial ports, as well as the cables for the power supply, reset cable, Keylock/Power LED, speaker and keyboard.

Get pdf Super P6DLH/P6DLF Motherboard User’s Manual

Aspiro Power Supply System User Manual

The Aspiro power system family is a highly configurable shelf solution designed to meet the requirements of modern telecommunication equipment. The power system includes fan-cooled, hot-swappable rectifiers with output power available at either 400 or 800 W per rectifier. System control is performed by the PCC which can be managed via controller display and push-buttons, using the PC-based PowCom TM software, or through a web browser with Ethernet connection. The power rack can be configured with a wide selection of distribution units.

System Configurations
The Aspiro power system is available in a variety of configurations to suit the specific needs for the installation site. Aspiro can be delivered either as a 1 Rack Unit (RU) or as a 2 RU system. The 1 RU system includes what is mentioned below as the Power Shelf, while the 2 RU system includes a Power Shelf and a Distribution Shelf. Each of the shelves are configurable with rectifier quantity, as well as distribution drawer quantity, circuit breaker type and quantity.

Get pdf Aspiro Power Supply System User Manual

LaCie Brick Hi-Speed USB 2.0 Desktop Hard Drive User’s Manual

Building on over a decade of design excellence, LaCie has created a new line of drives that are timeless and crafted to blend functionality with high-technology. These latest drives are performance-based solutions that will power you through your specific applications.

Ideal for speed intensive applications, the LaCie Brick Hi-Speed USB 2.0 Hard Drive handles the curves of your demanding data needs. Secure and stable, the LaCie Brick Hi-Speed USB 2.0 Hard Drive is an ideal way to add space to your computer; you can divide the drive into specific spaces (partitions) for different parts of your data, or leave it alone and simply use it as one big volume.

Getting Connected
Follow these steps to quickly get your LaCie Drive powered on and connected to your computer. To get started, go to: 2.1. Connect the Power Supply and Switch On the Drive or 2.2. Connect the USB 2.0 Cable to Your LaCie Drive and to Your Computer Once you’ve gotten the drive powered on and connected to your computer, move on to section 3. Using Your LaCie Drive for important information on how to format and utilize your drive.

Get pdf LaCie Brick Hi-Speed USB 2.0 Desktop Hard Drive User’s Manual

ModemUSB/E12 User Manual

ModemUSB/E12 is a device designed for data transmission via GSM Network. The user- friendly design allows you to directly connect the device to one of the USB ports of your PC/laptops. Once a SIM card is inserted in the modem and the device is connected to the PC, you would be able to send SMS or access internet via GSM networks (mobile networks). ModemUSB/E12 supports the following data-bearers: CSD, GPRS, EDGE and SMS.

The device should not be connected to PC before the installation of the drivers. SIM card is mandatory for setting up connection to the GSM network. However, the manufacturer of this equipment does not supply the SIM card. The SIM card can be purchased from your GSM (mobile) service provider!

For APN, user name and password please contact your GSM (mobile) service provider. The modem must be unplugged from the PC while inserting or taking out the SIM card. If the SIM card will be inserted or taken out from the modem while it is still plugged to the PC – it may cause damage to the modem or the SIM card. In this case, the modem will not be replaced or repaired under guarantee.

The modem can be unplugged from the PC only if it is disconnected from the Internet and the MTC is properly closed.
If the modem is unplugged properly from the PC wait for at least 10 seconds before plugging it back to the PC. Otherwise restart your PC before inserting modem back. You can find additional CE marking on the newest modem models as well in internal SIM holder with maximal powering instructions on it.

Get pdf ModemUSB/E12 User Manual

Electronic Gadgets Manuals

Archive

Labels