NOVA-7892 Socket 370 Celeron and Pentium III

NOVA-7892 Socket 370 Celeron and Pentium III

Welcome to the NOVA-7892 Socket 370 Celeron® and PentiumIII® ( FC-PGA ) with Multimedia & 100Base-T Ethernet & Dual View LCD Embedded Little Board. It is equipped with high performance Intel® Celeron up to 500MHz( or above ) and Pentium III ( FC-PGA ) 933MHz ( or above ) Processor and advanced high performance multi-mode I/O, designed for the system manufacturers, integrators, or VARs that want to provide all the performance, reliability, and quality at a reasonable price.

This board has a built-in DiskOnChip™(DOC) Flash Disk for embedded application. The DOC Flash Disk is 100% compatible to hard disk. User can use any DOS command without any extra software utility. The DOC currently is available from 2MB to 144MB.

An advanced high performance super AT I/O chip – Winbond W83977TF is used in the NOVA-7892 board. The on-chip UARTs are compatible with the NS16C550. The parallel port and IDE interface are compatible with IBM PC/AT architecture. NOVA-7892 uses the advanced VIA Apollo Pro133 chipset Chipset which is 100% ISA/PCI compatible chipset with PCI 2.1 standard. In addition, this board provides 168-pin sockets for its on-board DRAM. The DIMM module is 3.3V SDRAM and max. 256MB.

The VGA chip used on NOVA-7892 supports dual view LCD function which can display simultaneously on two monitors when you enter WINDOWS 95/98. In general, this function is achieved by two VGA chips.

Get pdf NOVA-7892 Socket 370 Celeron and Pentium III

MicroGuard 424 Installation Data

MicroGuard 424 Installation Data

This MicroGuard® 424 System Manual is designed to assist the fully trained and experienced crane technician in the safe and proper installation of the MicroGuard® 424 System. At no time may this System be used as a substitute for the usual safety practices and precautions required for the safe setup and operation of the crane.

DISPLAY
Mount the display in the cab where it can be easily observed without obstructing the view through the cab window. Position the display cable so that it will not hinder the normal operation of the levers and controls of the crane.

COMPUTER
Mount the computer inside or outside of the cab with the cable glands facing down. Ensure that there is enough cable line from the other sensors. Note: The cable to the pressure transducers cannot be increased by splicing in additional cable.

PRESSURE TRANSDUCERS
Do not remove the existing transducers in the hydraulic system unless a failure occurs. If the transducers are confirmed to have failed, then replace them accordingly. On upgrades from the RLI-200, it will be necessary to remove the connectors from the computer end of the cable. Do this, but cut the cable as close to the connector as possible. This will give you as much cable length as possible.

EXTENSION REEL CABLE TO COMPUTER
Connect the cable to the extension reel. Route the cable to avoid cable damage, i.e., cutting or pinching during the normal movement of the boom. When upgrading the existing extension reel with a new angle sensor and connector, use the following table for wiring at the extension reel terminal block. Use Appendices A-D for reference. Use Cable A047013 from extension reel to computer.

Get pdf MicroGuard 424 Installation Data

UWT Pocket PC Manual

UWT Pocket PC Manual

DELL Axim Checklist
Pocket PC Model 300
DELL Axim X5 User’s Guide
Dell Axim X5 Features Hardware Brochure
Dell Axim X5 Pocket PC Companion CD
DELL WiFi Card
Sync cable
External power/charging cable

Features Hardware Brochure
Get familiar with all the parts of the device
Care and handling of the Axim
Put in Owner Information
Pocket pc desktop (2nd item)
Click on Tap here to set owner information

Entering Information
Input Method: Start > Settings > Input icon
Tap on the small triangle at the bottom right of screen to switch between the 4 different input methods.
1. Block Recognizer (Palm)
2. Keyboard
3. Letter Recognizer (1st grade)
4. Transcriber – Write Notes in your own handwriting

Cleaning the Screen
Use a soft dry lens cleaning cloth like the type recommended for cleaning eyeglasses Do not use liquid or aerosol cleaners.

Batteries
The Axim has 2 types of batteries, a main battery and a backup battery. The backup battery is a CR2032 lithium battery. When installing either battery, make sure the device is turned off.
CAUTION: Do not remove the main battery and backup battery from the device at the same time

Get pdf UWT Pocket PC Manual

VITO Audio Notes User’s manual

VITO Audio Notes User’s manual

VITO AudioNotes, the easiest solution for taking notes just on the go. This application records your notes in MP3 or WAV format and plays them back. We hope you’ll enjoy using VITO AudioNotes as we do our best to provide you with the best solutions for your mobile lifestyle.

Recording notes
to record a new note:
• start AudioNotes from Start > Programs > AudioNotes and press the left soft key Record to pause/resume recording:
• press the right soft key or tap Pause in the bottom tray bar to stop recording:
• press the left soft key or tap Stop in the bottom tray bar To start playing/ recording from any chosen point:
• Play>Stop in the required place, then open drop down menu for this audio note Resume>Play or Record.

Note. AudioNotes will continue recording to this same audio note from the place where you stopped. Please note that after you press Resume > Record everything that was recorded to this audio note after the stop point will be rerecorded.

to change recording format:
• go Menu > Recording > Recording format and choose the necessary format for recording. Mind that high quality recording in WAV format requires more space. to change VAS:
• press the left soft key to start recording
• navigate with up and down joystick buttons to choose the VAS control panel
• press the left or right joystick button to change VAS level
Note: VAS (Voice Activated System) allows you to record only sounds that exceed the set VAS level. The loudness is indicated by flashing lights in the VAS panel and the Vas level is a yellow bar you can see in the VAS panel as well. Otherwise, when the loudness is not enough (the lights don’t reach the yellow bar), recording is paused

Get pdf VITO Audio Notes User’s manual