PowerAmplifier User Manual

PowerAmplifier User Manual

This power amplifier can be mast mounted using the stainless steel U-bolts as shown in Figure 5 and Figure 6. Refer to the sketch for proper positioning. Carefully tighten the bolts using the included nuts. Take care not to over-tighten the bolts or cause damage to the RF connectors on the amplifier. Because the amplifier is a sealed unit, these connectors can not easily be repaired. This unit can also be mounted to a flat surface using any of the mounting holes on the unit’s mounting flanges.

Radio transmitters, receivers and RF cables require protection when attracted by lightning strike.

The surge protectors contain fast response gas filled arrestors to provide low let through voltage for fast rise time transients. The device is configured to minimize circuit capacitance and the performance can be assured up to 2GHz. Standard models provide protection for receivers and transmitters up to a 1KW power level. Installing this device in outdoor may be subject to lightning strikes. To properly protect your equipment, you should install the lightning arrestor to prevent an electrical surge from traveling through the antenna cable and into the building. Lightning protection for a building is more forgiving than protection of electrical devices. A building can withstand up to 100,000 volts, but electrical equipment may be damaged by just a few volts.

Direct earth grounding of the antenna and the Lightning Protector is necessary to protect the installation from lightning and the build-up of static electricity. The ground terminal is located on the lightning protector that attached with this unit. Connect one end of the grounding cable to the Ground terminal and the other end to a good ground connection.

Get pdf PowerAmplifier User Manual

FocusTV PCI TV Card User Manual

FocusTV PCI TV Card User Manual

FocusTV PCI TV Card is a TV video watching & recording device design for all the new generation that enjoys the video world. The latest chip tech. for video processing not only provides highly video performance but support CATV/VHF/UHF full channel, external resource inputs (composite, S-video, and other AV equipments).FocusTV PCI TV Card concentrates on watching & Recording TV only, all saved efforts to put into video quality and performance instead to chaos useless functions. FocusTV built to enjoy TV life, built to focus on TV screen only.

System Requirement
CPU:
MPEG-1 Real-time Recording: Pentium-III 800 CPU or above
MPEG-2 Real-time Recording: Pentium-III 1.6G CPU or above
An available PCI 2.1 slot
Sound Card
Microsoft Windows 98SE / ME / 2000 /XP
640 x 480 display card(16-bit color)
128MB Ram
CD-ROM (for installation)
Hard disk(at least 10 Mb)
DirectX 8.1 or above

Caution:
Please not install the TV Card hardware without power off your computer; it might damage your computer and the TV Card. When the PC is running, you can’t touch the inside of your PC include the 6800 TV Card and the other device inside your PC.

Get pdf FocusTV PCI TV Card User Manual

Digital Video/Audio and Serial I/O Extender User’s Manual for the M5-2C2

Digital Video/Audio and Serial I/O Extender User’s Manual for the M5-2C2

M5-2C2-TR offers integrated extension of digital video, audio and RS-232 interface up to 50m (160ft) for HDMI/DVI. It maintains HD video signals up to WUXGA (1920×1200) at 60Hz refresh rate for PC and 1080p for HDTV. It is compatible with full DDC2B and HDCP. It supports connecting one of 3 different audio types in the transmitter; RCA, PDIF (Optic) or SPDIF (Coaxial) and outputting all 3 audio types. RS232 serial interface offers device-to-device and device-to-controller connections to build up control system for A/V integration. It is designed to multiplex and de-multiplex the DVI/HDMI video, digital/analog audio, Display Data Channel (DDC) command interface, High Definition Copy Protection (HDCP) and serial protocol so as to be linked over two CAT5 cables. It gives benefits of easy plug-and-go installation and offers you a cost effective solution for pro A/V system.

Shipping Group of M5-2C2 Digital Video/Audio and RS232 Extender
Tx and Rx boxes: One Uplink module & One Downlink module.
AC/DC power adapter: One +12V/3A unit (including AC cord).
User’s Manual
Option: DVI to HDMI cable, DVI cable, Dsub cable, Audio cable.

Hardware requirements
You have a graphic controller card with a DVI port in your Windows/Mac (Mac is option), or SUN system. It should support the maximum graphic resolution feature of the display to be connected.

In case of using a computer, no special memory size, CPU speed and chipsets are required. Proper initial trial of the entire platform with its application using a short length copper cable is recommended prior to install with the optical link.

Software requirements
No special needs, if the DVI graphic controller and display peripheral are operational with the platform’s OS and application

Get pdf Digital Video/Audio and Serial I/O Extender User’s Manual for the M5-2C2

SATEL I-LINK PC Point-To-Multipoint Program User Guide

SATEL I-LINK PC Point-To-Multipoint Program User Guide

SATEL I-LINK PC is a Point-to-Multipoint program, that can be used to drive several SATEL I-LINK 100 slaves connected to SATELLINE Radio Modems. The maximum number of slaves is 16. The program makes it possible to operate systems which are connected to the I/O -ports, to change values, monitor the radio link and Multipoint operation etc.

SATELLINE RADIO MODEM AND SATEL I-LINK 100 CONFIGURATIONS
BAUD RATE
Set the baud rate of the SATELLINE Radio Modem. Check that the other parameters are “N-8-1”.
Set the baud rate of the SATEL I-LINK100 by using the BAUD DIP -switches. 00=2.4, 10=4.8, 01=9.6, 11=19.2 (check that the SATELLINE Radio Modems have the same settings).
PROTOCOL
Set the SATEL I-LINK 100 PRTCL switch to the Multipoint position, P-to-MP.
ADDRESS
Set personal addresses to all SATEL I-LINK 100 sSlaves by using the ADDRESS DIP - switches.
CONNECTIONS
Before connecting the device to a power supply, first connect all inputs and outputs. There is more information about connections at the end of the manual.

START
Open the SATEL I-LINK PC program
OPERATION WINDOW
Open a new operation window from the toolbar list by clicking the -button on the upper left corner, or Open by clicking on the File Menu, opening “New Slave”. Open your own window to all slaves. Note that the maximum number of slaves in this program is 16. Arrange the display by using the Windows Menu or the -buttons.

COM PORT
Open the COM- port from the toolbar list by clicking “Master Config” and select “Open ComPort”. Set the same parameters as you have set for the SATELLINE Radio Modem and SATEL I-LINK 100, then press OK. If there are no COM -port settings, the program will automatically ask for them.

SLAVE ADDRESS
When the new Slave is opened, the program will automatically set the address for it. To make manual adjustments, click anywhere on the empty table using the right mouse button, and select “Set slave address”. Insert the new address, and then press OK.

Get pdf SATEL I-LINK PC Point-To-Multipoint Program User Guide